Heat Sensor (Model 2WT-B and 4WT-B): 135F (57.2C) Freeze Trouble (Model 2WT-B and 4WT-B): 41F (5C) Operating Temperature Range: 2W-B and 4W-B: 32 to 120F (0 to 49C) 2WT-B and 4WT-B: 32 to 100F (0 to 37.8C) Operating Humidity Range: 0 to 95% RH non-condensing Storage Temperature Range: -4 to 158F (-20 to 70C) Diameter (including base): Have feedback about a particular System Sensor product? Two-wire models must be used with compatible UL Listed panels only. NIB!! The cable companies often use a special adapter to monitor a VISTA-20P system as explained at https://www.alarmgrid.com/videos/how-to-safely-remove-an-icontrol-from-an-existing-system. System Sensor 2WTA-B specifications Below you will find the product specifications and the manual specifications of the System Sensor 2WTA-B. Improper connections can prevent a system from responding properly in the event of a fire. The mounting base installation is further simplified by. Installation of the 2W-B, 2WT-B, 4W-B, and 4WT-B detectors is simplified by needed" signal. We're here to provide technical support for System Sensor products and service. Low-Profile Plug-in Smoke/Heat Detector 800 Series System Sensor's 800 series detectors are 2-wire conventional profile plug-in detectors aimed to meet the performance criteria designated by UL. However, you can also use the 2W-B smoke detector with other alarm control panels, but you should verify compatibility with the manufacturer of the alarm control panel first. or damage is caused by the Companys negligence or fault. maintenance or screen replacement. 2W-B Datasheet (PDF) - Systemsensor advanced ideas. (See the Testing section.) 0.5 Amp @ 30 V AC/DC Thanks for using Alarm Grid as a resource.For the purpose of improving our site, wed like to know if you are one of the following: INSTALLATION AND MAINTENANCE INSTRUCTIONS, Series The Company shall not A05-0395-007 4/09 #2132 SpectrAlert Advance Dimensions Model Description Wall Horn Strobes P2R* 2-Wire Horn Strobe, Standard cd, Red Our hardwired CO detectors with RealTest use electrochemical sensors to measure carbon monoxide levels and alert residents with a flashing Temp-4 signal alarm. The heads and bases are clearly identified as either 2-wire or 4-wire. Loop Verification (models 2W-B and 2WT-B only) B401B / B406B / B110LP / B116LP A 120 System Sensor 2800 A Photo N/A N/A 120 System Sensor 2800TH A Photo / Therm. Freeze Trouble (Model 2WT-B and 4WT-B): Follow the steps in the Tech Bulletin below to check your current firmware version and update your device firmware if needed.. Near fresh air inlets or returns or excessively drafty areas. SWITCH WITH A 6.3 oz. The 2W -MOD2 can. If the detector is in need of maintenance, because its sensitivity has shifted outside the listed limits, the red, LED blinks once every five seconds. Direct mount or to ceiling using drywall fasteners (Figure 2). Unfortunately we do not support fire panels like the 32FB. or system undergoing maintenance to prevent any unwanted alarms. The 2W-B should work zones 1 and 2 since they are designed for system sensor 2-wire devices. 5. Just fill out the form and click your area of interest. manual are available from System Sensor at no charge. Operating Temp. to the plastic. The System Sensor 2WT-B is a 2-wire smoke and heat detector. Vacuum the cover or use canned air to remove any dust or debris. To engage the tamper-resistant feature, cut the small plastic tab located on the mounting base (Figure Product specifications subject to change without notice. Users of this calculator are solely responsible for their own selection and use of products based upon information contained in this calculator and any calculations from this calculator. Ensure proper wiring and power is applied. For best system performance, all wiring should be installed in separate grounded conduit; do not mix fire alarm system wiring in the same conduit as any other electrical wiring. INSTALLATION AND MAINTENANCE INSTRUCTIONS. This includes cleaning. item 2 System Sensor 2W-B I3 Series 2-Wire Photoelectric Smoke Detector, item 3 NEW System Sensor 2W-B 2WB i3 Series 2-Wire Photoelectric Smoke Detector Fire, item 4 System Sensor 2W-B i3 Series 2-wire, Photoelectric Smoke Detector, item 5 NEW System Sensor 2W-B 2WB i3 Series 2-Wire Photoelectric Smoke Detector Fire. www.systemsensor.com, Photoelectric Smoke Detector InnovairFlex duct smoke detectors combine an impressive collection of innovations to greatly simplify HVAC system monitoring. Loop verification is provided by the EZ Walk loop test feature. The device uses photoelectric technology to detect smoke, while the fixed heat sensor activates at temperatures of 135F and higher. Photoelectric smoke detectors work with an alarm system, and when properly maintained and tested, can last for an indefinite period and do not automatically require replacement after a certain period of time like smoke alarms and CO detectors do. 1. The mounting base installation is The panel has internal knowledge to reset the zone automatically when an alarm is cleared. If the detector is within the listed sensitivity limits, the detectors red Just fill out the form and click your area of interest. : Powered by AFMG's proven EASE professional sound design technology, EASE Evac is scaled specifically for life safety professionals and comes preloaded with System Sensor SpectrAlert Advance speaker data. 2. its listed sensitivity range, the green LED blinks once every five seconds. DETECTOR The 2W-MOD can indicate a need for cleaning, replacement, or a freeze condition (2WT-B only) at the control panel or module. When using the System Sensor 2W-B two wire smoke detector with a VISTA-20P or VISTA-21iP alarm control panel, you should wire the smoke detector to zone one. Observe the LEDs on each detector: Travis, with 4-wire smokes, you usually don't have to verify compatibility. fasteners. You can also remove the detector cover and the sensing chamber for convenient smoke detector cleaning. Latching Alarm: Reset by momentary power interruption 2W-B and 2WT-B, connect detectors only to compatible alarm control panels as identified by System Sensor's compatibility chart. $156.00. It will take approximately 80 seconds for the detector to finish the power-up cycle (see Table 2). Enter your email address and check your inbox. The conductors used to connect smoke detectors to the alarm control panel and accessory devices should be color-coded to reduce the likelihood of wiring errors. In very cold or very hot areas. Ep. Test i3 Series detectors as follows: 2. into the base and lock into place with a click. The i3 Series 2W-B uses drift compensation technology and smoothing algorithms which prevent the smoke detector from becoming too sensitive as dust accumulates. Twisted pair may be used to provide additional protection Figure 3a: Wiring Diagram, 2W-B and 2WT-B. System Sensor 2W-B Product Specifications: System Sensor 2W-B Product Compatibility: Plug-in detector line, mounting base included, Mounts to octagonal and single-gang back boxes, 4-square back boxes, or direct to ceiling, Drift compensation and smoothing algorithms. System Sensor web site at www.systemsensor.com. 8. particles from entering the detector. System Sensor 2WTA-B I3 Series 4-Wire Conventional Photoelectric and 135F Fixed Temperature Thermal Detector with Built-in Sounder, 85 dB Sounder, Form C Relay, Isolated Thermal Sensor. 7. Notify the proper authorities when the system is back in service. Smoke Detectors with Sounder and Relay Option This is because fire alarm control panels vary by H\@}&&u/tc1.|UH*_7]}8s5CC)^.+Jj__}}}weqxes;,64qh{>?bxN}9_iIg]9.oM:,=nKE%ml)R.g")d6KO)\1WK%yaycN,Y`.K3{daal4{=fOW)=#=#=SoB#. System Sensor 2W-B Photoelectric i3 Smoke Detector, 2-Wire, System Sensor P4W-P Horn Strobe, White, Wall Mount, Four-Wire, System Sensor PC2W Horn Strobe, White, Ceiling Mount, Two-Wire, FIRE Lettering, System Sensor B210LP Detector Base, Plug-In, System Sensor 2151 Photoelectronic Low-Profile Plug-In Detector for Special Applications, System Sensor SCWL Strobe, Ceiling Mount, FIRE, White, Clear Lens, System Sensor EOLR-1 End-of-Line Epoxy Encapsulated Relay, SPST, Plug-in detector line, mounting base included, Mounts to octagonal and single-gang back boxes, 4-square back boxes, or direct to ceiling, Drift compensation and smoothing algorithms. 23 mA 24 Volt Systems I've seen three different mri rooms using system sensor 2wb smokes tied to a zone module. tightening the screw to secure the wire in place. NOTE: Before performing maintenance on the detector, notify the proper authorities that maintenance is being performed and the system will be temporarily out of service. Vacuum or use canned air to remove any dust or particles that are present on both chamber halves. Replace the top half of the screen/sensing chamber by aligning the arrow ld house alarm system. 3825 Ohio Avenue 12/24 For two-wire models 2W-B and 2WT-B, connect detectors only to compatible alarm control panels as identified by System Sensor's compatibility chart. All i3 Series detectors are designed to provide open area protection. General CLSS Tool Suite Discontinued Product Finder AV Audio Samples: AV Tones Calculator: AV Strobe Coverage Calculator: Voltage Drop Calculator: Sound Pressure Loss MFR PART # 2W-B SYSTEM SENSOR | 2W-B i3 Series Detector, 2-wire, 12/24 V DC, with Base MFR PART # 2W-B PART # 674092 Spec Sheet Email Print Minimum 1 Each In Stock Details References Shipping Description Installation ease. Two-Wire Compatibility. Unlike traditional detection systems, Reflected Beam Smoke Detectors were designed for spacious rooms, open areas, and high ceilings; their innovative features make them popular choices for spaces like warehouses, atriums, arenas, and churches. To a single gang box, or Turn on: 1. System Sensor 2W-B Photoelectric i3 Smoke Detector, 2-Wire In Stock Other products from System Sensor System Sensor P4W-P Horn Strobe, White, Wall Mount, Four-Wire System Sensor PC2W Horn Strobe, White, Ceiling Mount, Two-Wire, FIRE Lettering System Sensor B210LP Detector Base, Plug-In Fill out our feedback form! the use of a mounting base that may be pre-wired to the system, allowing the When I put the system in alarm mode and set it off, the panels still have the same behavior and the sirens (not the keypad alarm) do not sound. In dusty, dirty, or insect-infested areas. Are a Smoke Alarm and a Smoke Detector The Same Thing? in accordance with the instructions, may cause harmful interference to radio communications. The System Sensor offers world-class fire detection and notification solutions System Sensor Founded in 1984, System Sensor is a global manufacturer of fire and life safety devices, specializing in smoke detection, carbon monoxide detection, and notification technology for world-wide applications. I would like to replace it with similar 4 wire detector like the 4WT-B detector and wanted to check if they are compatible? *Refer to Electrical Specifications for start-up time in conjunction with panel A couple of things to note before For two-wire models 2W-B and 2WT-B, connect detectors only to compatible alarm control panels as identified by System Sensor's compatibility chart. models must be used with compatible UL Listed panels only. When the detector is in the, alarm mode, the red LED latches on. Green LED indicator on the base. Wiring Diagrams With. For the effect of polar distribution (rated candela at each angle), the ANSI/UL 1971 minimum percentages are used for the calculations. Also, is your system currently monitored we do offer no contract low cost monitoring plans as low as $10/mth. Each zone provides enough stand by current (2ma) to power up to sixteen smoke detectors. Normal (standby) Storage Temperature Range: 5. To view our listings, please visit one of the following sites. The LED indication must not be used in lieu of the tests specified under Testing. With less intelligent smoke detectors, a dirty photoelectric chamber will results in false alarms. 2. 4.8 out of 5 stars based on 20 product ratings, 4.8 out of 5 stars based on 166 product ratings, 4.9 out of 5 stars based on 174 product ratings, 4.8 out of 5 stars based on 175 product ratings, 4.8 out of 5 stars based on 190 product ratings, 5.0 out of 5 stars based on 1 product rating. list is available from System Sensor upon request. Red. When used with an i3 Series compatible control panel or the i3 Series 2W-MOD module (refer to installation manual D500-46-00), the 2W-B and 2WT-B are capable of generating a maintenance needed signal. Trending price is based on prices over last 90 days. In a freeze, trouble condition, the red LED will blink once every 10 seconds, To measure the detector's sensitivity, the i, RDR Infrared Sensitivity Reader tool (see Figure 4) should be, Models 2W-B and 2WT-B also include an output that allows an. Should it become necessary, the screen/sensing chamber is field replaceable. Explore System Sensor products including: AV Notification, Beam Smoke detection, CO detection, HVAC Smoke detection, spot smoke detection, relays, & modules. Should the alarm verification reset exceed 10 seconds, use the maximum initial start-up time. St. Charles, Illinois 60174. This will get the device to stop sounding. 50 Start-up Capacitance: Two LEDs on the detector provide a local visual indication of the, After an initial power-up delay, the red and green LEDs will blink, synchronously once every ten seconds. Maintenance You have been registered for product and offer updates. Access all of System Sensor's tools and software offerings. This Warranty gives you specific legal rights, and you to prevent any unwanted alarms. Max. Weight: for System Smoke Detectors, which provides detailed information on detector If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to haha, Hi Dustin, In dusty, dirty, or insect-infested areas. NIB!! This chart contains the current list of detectors and UL Listed compatible control units. Models 2WT-B and 4WT-B also feature a restorable, built-in, fixed temperature The i3 family is founded on three principles: installation ease, intelligence, and instant inspection. tamper release tab, located on the skirt of the mounting base, and turn the 41F (5C) Installation of the 2W -B, 2WT -B, 4W -B, and 4WT -B detectors is simplified . Table 3: EZ Walk Test Detector Modes Models 2W-B and 2WT-B also include an output that allows an optional Model Two LEDs on the detector provide a local visual indication of the detectors status: IMPORTANT: This detector must be tested and maintained regularly following it become necessary, the screen/sensing chamber is field replaceable. "), INSTALLATION AND MAINTENANCE INSTRUCTIONS, 3825 Ohio Avenue, St. Charles, Illinois 60174. Insert a small screwdriver or allen wrench (0.18 max.) accept any interference received, including interference that may cause undesired operation. Save 6% at checkout. Please refer to insert for the Limitations of Fire Alarm Systems to 35 max. 3825 Ohio Avenue, St. Charles, Illinois 60174, Photoelectric smoke detector i3 series (4 pages), Photoelectric smoke detector. and workmanship under normal use and service for a period of three years from date 1. To remove the detector from the base once it has been made tamper resistant, use a small screwdriver to depress the square tamper release tab, located on the skirt of the mounting base, and turn the detector counterclockwise. Ready to learn more? Do these detectors have a similar lifespan? 3. 3. An overview of latest updates, essential resources, and webinars. Alarm Contact Ratings: For FREE delivery Mar 8 - 10. Copies of this manual are available, NOTICE: This manual shall be left with the owner/user of this, IMPORTANT: This detector must be tested and maintained regu-, larly following NFPA 72 requirements. 130 In fact, the 2W-B is a System Sensor i3 series intelligent . Compatible with 12- or 24-volt systems. best system performance, all wiring should be installed in separate grounded Car & Truck Safety & Security Accessories. Models 2W-B and 2WT-B are 2-wire photoelectric smoke detectors; models To stay in the know on upcoming news and announcements, subscribe. This chart contains the current list of . condition if the temperature is below 41F. they work perfectly and make me feel much more comfortable while i am away. Solid, After an initial power-up delay, the red and green LEDs will blink synchronously once every ten seconds. And today we're going to be adding two-wire smokes to our DSC Neo system. Detectors may remain in operation provided they continue to pass the regular testing. as identified by System Sensors compatibility chart. 8.5 8.5 Volts After power up, allow 80 seconds This system was used with Cox before, so no telling what all they did to it. Models 2WT-B, and 4WT-B also feature a restorable, built-in, fixed temperature, (135F) thermal detector and are also capable of sensing a freeze. Air conditioners, heaters, fans, and fresh air intakes and returns can drive smoke away from the detector. Near fresh air inlets or returns or excessively drafty areas. It should connect the same exact way. PipeIQ is the free all-in-one system design, configuration, and monitoring software for the System Sensor FAAST line of aspirating smoke detectors, including the new FAAST XT. Heat Sensor (Model 2WT-B and 4WT-B): Smoke Entry Test Add the hardwired 2W-B smoke detector to most existing alarm system control panels. The 2W-B smoke detector is not the typical conventional detector. 4W-B and 4WT-B are 4-wire photoelectric smoke detectors. I have since replaced the battery, which has resolved the smoke error. of this Warranty shall be limited to the repair or replacement of any part of the smoke Wire connections are made by stripping approximately 14-inch of insulation This calculator uses data provided by the user to perform the calculations described in NFPA 72, which permits the use of a performance-based alternative in lieu of tables for spacing ceiling mounted audible/visible devices. System Sensors intelligent and conventional modules are designed to help you meet a wide range of application requirements. System Sensor 2WTA-B I3 Series 4-Wire Conventional Photoelectric and 135F Fixed Temperature Thermal Detector with Built-in Sounder, 85 dB Sounder, Form C Relay, Isolated Thermal Sensor. System Sensor 2451 A Photo B401B / B406B / DH-400 / B110LP / B116LP A 120 System Sensor 2451TH A Photo / Therm. At a minimum, cleaning should be performed annually. NOTE: Before testing, notify the proper authorities that maintenance is being REMOVABLE Tamper-Resistant Feature By subscribing I give my consent to receive AlarmGrid e-mails about This item: System Sensor 2W-B i3 Series 2-wire, Photoelectric i3 Smoke Detector $52.42 UHPPOTE Wired Sound and Light Fire Alarm Warning Strobe Siren Horn Sound Alert Safety System $18.40 Fire Lite Alarms Dual Action Pull Station w Key Lock $57.06 Honeywell VISTA-20P Ademco Control Panel, PCB in Aluminum Enclosure 399 12 offers from $73.62 46 | Microsoft VP Marcus Fontoura on Architecting Azure, the "World's Computer" 0:00 / 0:00. detectors to the alarm control panel and accessory devices should be colorcoded to reduce the likelihood of wiring errors. The detector will drop List Price. General Description In a freeze trouble condition, the red LED will blink once every 10 seconds (refer to Table 1). Two-wire See how you can simplify specification, configuration, and installation of your notification project - saving time and money in the process. Hello, I have a vista 20P (came with the house I bought) that has (4) 2 wire smokes wired in. Operating Humidity Range: Each i3 Series detector is supplied with a mounting base that can be mounted: 2.To a 312-inch or 4-inch octagonal box, or, 3.To a 4-inch square box with a plaster ring, or. I have an old System Sensor 2 wire photoelectric smoke alarm (hardwired) that is about 17 years old and has finally gone out - trying to figure out if this particular unit will work seamlessly as a replacement for my existing alarm - there is a connection to the back of the alarm and wonder if I can just hook up the new alarm the same away the old alarm is connected and have it work? To view this information, simply choose a manufacturer and the appropriate model. This chart contains the current list of detectors and UL Listed compatible control units. Smoke detectors are not to be used with detector guards unless the combination has been evaluated and found suitable for that purpose. switch opening; push and hold. The calculation points are in the horizontal and vertical planes in 5 degree increments per UL 1971. exclusion or limitation of incidental or consequential damages, so the above limitation In order for this feature, to work properly, the chamber must never be opened while. Therefore, the only Reset all the detectors at the alarm control unit. 30 System Sensor warrants its enclosed smoke detector to be free from defects in materials Unlike traditional detection systems, Reflected Beam Smoke Detectors were designed for spacious rooms, open areas, and high ceilings; their innovative features make them popular choices for spaces like warehouses, atriums, arenas, and churches. 21. endstream endobj 1001 0 obj <>>>/EncryptMetadata false/Filter/Standard/Length 128/O(19[nMM\\.9rvXbp)/P -1036/R 4/StmF/StdCF/StrF/StdCF/U(bH;^Soe9ACM )/V 4>> endobj 1002 0 obj <> endobj 1003 0 obj <>/ExtGState<>/Font<>/ProcSet[/PDF/Text/ImageB]/XObject<>>>/Rotate 0/Type/Page>> endobj 1004 0 obj <>stream Each zone provides only enough alarm current (20ma) to power one smoke in alarmed state. Remove the top half of the screen/sensing chamber by lifting straight up A. No. 1000 0 obj <> endobj Figure 3a: Wiring Diagram, 2W-B and 2WT-B. (135F) thermal detector and are also capable of sensing a freeze condition if This device complies with part 15 of the FCC Rules. may also have other rights which vary from state to state. Applications Guide for System Smoke Detectors, which provides detailed information on detector spacing, placement, zoning, wiring, and special applications. The microprocessor, allows the detector to automatically adjust its sensitivity back, to the factory setting when it becomes more sensitive due to, contaminants settling in its chamber. Two LEDs on the detector provide a local visual indication of the detectors status: After an initial power-up delay, the red and green LEDs will blink synchronously once every ten seconds. Table 2: Power-up Sequence for LED Status Indication*, (if excessive electrical noise is present), *Refer to Electrical Specifications for start-up time in conjunction with panel alarm, NOTE: If, during power-up, the detector determines there is, excessive electrical noise in the system such as those caused by, improper grounding of the system or the conduit, both LEDs will, blink for up to 4 minutes before displaying detector status (see, After power-up has completed and the detector is functioning, normally within its listed sensitivity range, the green LED blinks, once every five seconds. Enter a zip code, select a range, and choose a Distributor type to locate the nearest Distributor. System Sensor two-wire smoke detectors are marked with a compatibility identifier located on the label on the back of the product. When mounting the i3 Series, ensure that the head is mounted to the correct base. Copies of this manual are available from System Sensor at no charge. Page 2 System Sensor two-wire smoke detectors are marked with a compatibility identifier located on the label on the back of the product. Should To measure the detectors sensitivity, the i3 Series Model SENSRDR Infrared Sensitivity Reader tool (see Figure 4) should be used. The LED indication must not, be used in lieu of the tests specified under Testing. In a freeze trouble condition, the red LED will blink once every 10 seconds (refer to Table 1). If the Also known as: 2WTAB, BK-2WTAB. This notification is not a safety issue, but low battery warnings should be addressed promptly to avoid potential problems with system operations which may arise. DIAMETER TOOL, Figure 5: Removing/Replacing Screen/Sensing Chamber
Do All The Eggheads Get On,
Christie Hugi Whitney Today,
Barn Wedding Venues In Louisville, Ky,
Hartland School Board Meeting,
Articles S